Dodge Journey: Muffler, exhaust

REMOVAL

MUFFLER

Exhaust System
Fig. 16: Muffler/Exhaust Pipe Assembly - Single Tail Pipe

  1. - INSULATOR
  2. - MUFFLER/EXHAUST PIPE ASSEMBLY
  3. - BAND CLAMP

NOTE: Band clamps (3) are spot welded to exhaust system. If a band clamp must be replaced, the spot weld must be ground off the exhaust pipe.

NOTE: When replacement is required on any component of the exhaust system, it is most important that original equipment parts (or their equivalent) be used.

Exhaust System
Fig. 17: Muffler/Exhaust Pipe Assembly - Dual Tail Pipe

  1. - INSULATOR
  2. - MUFFLER/EXHAUST PIPE ASSEMBLY
  3. - BAND CLAMP

1. Raise vehicle on hoist.

2. Apply penetrating oil to band clamp (3).

3. Remove band clamp (3).

4. Remove ground strap from muffler (2).

CAUTION: Do not use any tools to remove the rubber isolators-remove by hand only. Soapy water or silicone based lubricant spray may be used to assist removal/installation of isolators. DO NOT use a petroleum based lubricant on the isolators, as damage to the rubber material can occur.

5. Remove support isolators from muffler supports.

6. Remove the one muffler/resonator assembly.

INSTALLATION

MUFFLER

Exhaust System
Fig. 18: Muffler/Exhaust Pipe Assembly - Dual Tail Pipe

  1. - INSULATOR
  2. - MUFFLER/EXHAUST PIPE ASSEMBLY
  3. - BAND CLAMP

NOTE: Always work from the front to rear of exhaust system when aligning and tightening exhaust system components.

Exhaust System
Fig. 19: Muffler/Exhaust Pipe Assembly - Single Tail Pipe

  1. - INSULATOR
  2. - MUFFLER/EXHAUST PIPE ASSEMBLY
  3. - BAND CLAMP

1. Position muffler/resonator assembly (2) onto exhaust pipe.

2. Install support isolators.

3. Align muffler and resonator assembly to maintain position and proper clearance with underbody parts.

All support isolators should have equal load on them.

4. Install new band clamp (3). Tighten to 54 N.m (40 ft. lbs.).

5. Connect ground strap to muffler (2).

6. Lower vehicle.

7. Start the engine and inspect for exhaust leaks. Repair exhaust leaks as necessary.

8. Check the exhaust system for contact with the body panels. Make the necessary adjustments, if needed.

    Installation
    DIESEL PARTICULATE FILTER Fig. 12: Engine Support Bracket Bolts 1. Position the DPF and turbocharger gasket into the vehicle. Do not tighten at this time 2. Tighten the three bolts (1) at the ...

    Pipe, exhaust
    REMOVAL 2.7L/3.5L Fig. 20: Exhaust Pipe - 2.7L/3.5L - EXHAUST PIPE - NUTS - CROSS UNDER PIPE - GASKET WARNING: The normal operating temperature of the exhaust system is ver ...

    See also:

    Removal
    FRONT 1. Raise and support the vehicle. Fig. 163: TIRE AND WHEEL MOUNTING 2. Remove the wheel mounting nuts (3), then the tire and wheel assembly (1). NOTE: In some cases, it may be necessary ...

    TIRES — GENERAL INFORMATION
    Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: Safety WARNING: • ...

    Module, heated seat
    DESCRIPTION Fig. 35: Locating Heated Seat Module The heated seat module (2) is located under the driver front seat. It has a single electrical connector (1) and a push pin style retainer that s ...

    0.0097