Dodge Journey: Rocker arm, valve

DESCRIPTION

2.7L DOHC Engine
Fig. 133: Rocker Arm

  1. - LASH ADJUSTER POCKET
  2. - OIL SQUIRT HOLE
  3. - ROLLER

The rocker arms are composed of steel stamping with an integral roller bearing. The rocker arms incorporate a 0.5 mm (0.0197 in.) oil hole in the lash adjuster socket for roller/camshaft lobe lubrication.

REMOVAL

2.7L DOHC Engine
Fig. 134: Cylinder Head Cover Fasteners

  1. - DOUBLE ENDED STUDS
  2. - BOLTS

1. Remove cylinder head cover(s).

CAUTION: Always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

2. Rotate engine until the cam lobe is on its base circle (heel), on the rocker arm being removed.

2.7L DOHC Engine
Fig. 135: Rocker Arm - Removal/Installation

  1. - SPECIAL TOOL 8215A
  2. - SPECIAL TOOL 8216A
  3. - 3/8" DRIVE RATCHET

CAUTION: Depress valve spring only enough to remove rocker arm.

3. Using Special Tools 8215A (1) and 8216A (2) Adaptor, depress valve spring only enough to release tension on rocker arm.

4. Remove rocker arm from cylinder head.

CAUTION: If rocker arms are to be reused, identify position of rocker arms for reassembly in their original positions.

5. Repeat procedure for each rocker arm removed.

6. Inspect the rocker arm for wear or damage.

INSPECTION

2.7L DOHC Engine
Fig. 136: Rocker Arm

  1. - LASH ADJUSTER POCKET
  2. - OIL SQUIRT HOLE
  3. - ROLLER

Inspect the cam follower assembly for wear or damage. Replace as necessary.

INSTALLATION

2.7L DOHC Engine
Fig. 137: Rocker Arm - Removal/Installation

  1. - SPECIAL TOOL 8215A
  2. - SPECIAL TOOL 8216A
  3. - 3/8" DRIVE RATCHET

1. Lubricate rocker arms with clean engine oil before installation.

2. Rotate engine until cam lobe is on its base circle (heel) of rocker arm being installed.

3. Using Special Tools 8215A (1) and 8216A Adaptor, depress valve spring only enough to install rocker arm.

4. Install rocker arm in original position (if reused) over valve and lash adjuster. Release tension on valve spring.

NOTE: Inspect rocker arm for proper engagement into lash adjuster and valve tip.

5. Repeat procedure for each rocker arm being installed.

2.7L DOHC Engine
Fig. 138: Cylinder Head Cover Fasteners

  1. - DOUBLE ENDED STUDS
  2. - BOLTS

6. Install cylinder head cover(s).

    Lifter(s), hydraulic
    Diagnosis and Testing DIAGNOSIS AND TESTING - HYDRAULIC LASH ADJUSTER NOISE DIAGNOSIS Proper noise diagnosis is essential in locating the source of a NVH complaint. Locating a lash adjuster (tappe ...

    Seal(s), valve guide
    REMOVAL Fig. 139: Valve Stem Seal-Removal/Installation - VALVE SEAL TOOL - VALVE STEM 1. Remove valve spring. 2. Remove valve stem seal by using a valve seal tool. INSTALLATION Fig. ...

    See also:

    Assembly
    HOUSING-AIR DISTRIBUTION NOTE: LHD model with A/C shown in illustrations. RHD and heater-only models similar. Fig. 115: Mode Door Levers-Removal/Installation 1. If removed, install the fo ...

    REPLACEMENT PARTS
    Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the use of non-MOPAR parts for mainten ...

    Removal
    NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness. SATELLITE AUDIO ONLY 1. Disconnect and isolate the batter ...


    0.0088