Dodge Journey: Installation

Manual Transmission BG6
Fig. 137: Rear Mount Bracket

1. If transmission brackets were removed or transmission was replaced install the rear mount bracket and tighten (1) to 100 N.m (74 ft. lbs.).

Manual Transmission BG6
Fig. 138: Front Mount Bracket

2. If transmission brackets were removed or transmission was replaced install the front mount bracket and tighten (1) to 100 N.m (74 ft. lbs.) and (2) to 133 N.m (98 ft. lbs.).

Manual Transmission BG6
Fig. 139: Left Mount Bracket

3. If transmission brackets were removed or transmission was replaced install the left mount bracket and tighten (1) to 100 N.m (74 ft. lbs.).

Manual Transmission BG6
Fig. 140: Bellhousing Bolts

4. Lift transmission into position.

5. Install the lower transmission bolts (2) and tighten to 58 N.m (43 ft. lbs.) torque.

Manual Transmission BG6
Fig. 141: Rear Mount

6. Install the rear transmission mount (5) to cradle.

7. Install rear transmission mount bolts and tighten to 68 N.m (50 ft. lbs.).

8. Install the rear mount bracket to transmission bolts (2, 3) and tighten to 68 N.m (50 ft. lbs.).

9. Roll engine and transmission back into place.

10. Install rear mount through bolt (4) and tighten to 68 N.m (50 ft. lbs.).

11. Install the starter.

12. Install the transmission cross member and tighten to 68 N.m (50 ft. lbs.).

13. Install the front transmission mount through bolt (4) at this time and tighten to 50 N.m (37 ft. lbs.).

14. Remove the jacks.

15. Lower the vehicle.

Manual Transmission BG6
Fig. 142: Bellhousing Bolts

16. Use a floor jack to raise transmission into position.

17. Install the upper transmission mount and tighten to 100 N.m (74 ft. lbs.).

18. Raise the vehicle on the hoist.

19. Install halfshafts.

20. Fill transmission fluid to proper level. See Standard Procedure .

21. Lower hoist.

22. Connect all wiring harness connectors and insure correct wiring harness is routed correctly.

Manual Transmission BG6
Fig. 143: Hydraulic Line

23. Install shift cables (2) into bracket until a click is heard.

24. Snap the ball-socket end fittings onto the shift lever ball-studs.

25. Install the bolt for clutch hydraulic line (3) and tighten to 11 N.m (105 in. lbs.).

26. Install the clutch hydraulic line (1) to slave cylinder.

Manual Transmission BG6
Fig. 144: Bleeder At Slave Cylinder

27. Install hydraulic line (1), bleed adaptor (2) and clip at the slave cylinder.

28. Bleed the slave cylinder.

29. Install the negative battery cable.

30. Install air cleaner assembly.

SPECIFICATIONS

GENERAL SPECIFICATIONS

GEAR RATIOS

TORQUE SPECIFICATIONS

SPECIAL TOOLS

Manual Transmission BG6
Fig. 145: Universal Handle C-4171

Manual Transmission BG6
Fig. 146: Seal Installer 6709

Manual Transmission BG6
Fig. 147: Remover, 9664

Manual Transmission BG6
Fig. 148: Installer L-4520

Manual Transmission BG6
Fig. 149: Installer 9935

Manual Transmission BG6
Fig. 150: Installer 9928

Manual Transmission BG6
Fig. 151: Puller 7794-A

Manual Transmission BG6
Fig. 152: C-4657 Seal Installer

Manual Transmission BG6
Fig. 153: Installer 9589

Manual Transmission BG6
Fig. 154: Installer D-111

Manual Transmission BG6
Fig. 155: Installer, Cup - D-144

Manual Transmission BG6
Fig. 156: Bearing Splitter, P-334

Manual Transmission BG6
Fig. 157: Fixture, 8925

Manual Transmission BG6
Fig. 158: Puller 9647

Manual Transmission BG6
Fig. 159: Sleeve C-3717

Manual Transmission BG6
Fig. 160: Torque Tool C-4995

    Assembly
    Fig. 65: Remove Input Shaft Bearing Cup NOTE: Always use ATF on all moving parts during this assembly procedure. 1. Use Bearing Cup Remover 9664 (2) and appropriate Slide Hammer (1) to r ...

    Cable, gearshift control
    REMOVAL Fig. 161: Shift Cables & Bracket 1. Remove the shifter. 2. Raise hood. 3. Remove the resonator. 4. Remove engine cover. 5. Remove air cleaner assembly. 6. Disconnect ne ...

    See also:

    Tray, battery
    DESCRIPTION The battery is placed and secured in a stamped steel battery tray. The battery tray is located in the left front side of the vehicle, just ahead of the left front wheel and tire assemb ...

    Seal, axle drive shaft
    REMOVAL Fig. 197: Axle Shaft Seal Removal 1. Remove axle shaft. 2. Insert a flat-blade pry tool (2) at outer edge of axle shaft seal (1). 3. Tap on the pry tool (2) with a small hammer and ...

    Installation
    CAUTION: Be certain to adjust the refrigerant oil level when servicing the A/C refrigerant system. Failure to properly adjust the refrigerant oil level will prevent the A/C system fro ...

    0.0082