Dodge Journey: Installation

SATELLITE AUDIO ONLY

NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness.

1. Route the cable behind the glove box, up to the radio and secure.

2. Connect the antenna to the radio.

3. Install the radio.

4. Install the glove box.

5. Route the antenna cable along the path of the old antenna wiring harness, securing where necessary.

6. Install the passenger side cowl panel.

7. Install the passenger side quarter trim panel.

8. Install the passenger side scuff plates.

9. Install the passenger side C-pillar.

10. Install the antenna base to the roof of the vehicle.

11. Install the antenna bracket and mounting fastener.

12. Install the antenna cable(s).

13. Install the headliner.

14. Connect the battery negative cable.

SATELLITE AUDIO AND VIDEO

AUDIO CABLE TO MODULE

NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness.

1. Connect the antenna cable to the module located under the front passenger seat.

2. Route the antenna cable along the path of the old audio antenna wiring harness, securing where necessary.

3. Install the passenger side cowl panel. 4. Install the passenger side quarter trim panel.

5. Install the passenger side scuff plates.

6. Install the passenger side C-pillar.

7. Install the antenna base to the roof of the vehicle.

8. Install the antenna bracket and mounting fastener.

9. Install the antenna cable(s).

10. Install the headliner.

11. Position the passenger seat to its original position.

12. Connect the battery negative cable.

VIDEO CABLE TO MODULE

NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness.

1. Connect the antenna cable to the module located under the passenger seat.

2. Route the antenna cable along the path of the old audio antenna wiring harness, securing where necessary.

3. Install the passenger side cowl panel.

4. Install the front passenger side scuff plate.

5. Install the antenna base to the roof of the vehicle.

6. Install the antenna bracket and mounting fastener.

7. Install the antenna cable(s).

8. Install the headliner.

9. Position the passenger seat to its original position.

10. Connect the battery negative cable.

SIGNAL (RADIO FEED) ANTENNA CABLE FROM MODULE TO COWL

NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness.

1. Connect the antenna cable to the instrument panel antenna cable in the cowl area.

2. Route the antenna cable along the path of the old audio antenna wiring harness, securing where necessary.

3. Connect the antenna cable to the module.

4. Install the passenger side cowl panel.

5. Install the front passenger side scuff plate.

6. Position the passenger seat to its original position.

7. Connect the battery negative cable.

SIGNAL (RADIO FEED) ANTENNA FROM COWL TO RADIO

NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness.

1. Connect the antenna to the radio.

2. Route the antenna cable along the path of the old audio antenna wiring harness, securing where necessary.

3. Install the radio.

4. Install the glove box.

5. Install the passenger side cowl panel.

6. Connect the battery negative cable.

    Removal
    NOTE: The antenna cables are integrated into the body wiring harnesses. New antenna cables is overlaid on the body wiring harness. SATELLITE AUDIO ONLY 1. Disconnect and isolate the batter ...

    Camera
    ...

    See also:

    Geartrain, planetary
    DESCRIPTION Fig. 355: Identifying Planetary Geartrain Components - FRONT SUN GEAR ASSEMBLY - #6 THRUST BEARING - #7 THRUST BEARING - REAR CARRIER/FRONT ANNULUS ASSEMBLY - REAR SUN GEAR ...

    Assembly
    Fig. 214: First Gear Needle Bearing & Output Shaft NOTE: Use ATF on all parts that are to be assembled in this procedure. 1. Install the first and first gear needle bearing (2) on the out ...

    Installation
    CAUTION: When installing a NEW brake caliper it is necessary to bleed the brakes using a special procedure which has been integrated to this installation procedure. Fig. 76: R ...

    0.0182