Dodge Journey: Installation

NOTE: Perform 1 through 6 on each side of vehicle to complete pad set installation, then proceed to 7.

CAUTION: Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the parking brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor, Special Tool 8807, as described below. Any other seating method will damage the self-adjuster mechanism.

Brakes
Fig. 128: SEATING PISTON WITH SPECIAL TOOL

1. If necessary, seat (bottom) the caliper piston in the bore as follows:

  1. Assemble a 3/8 in. drive ratchet handle and an extension (3).
  2. Insert the extension through Special Tool 8807-1 (2).
  3. Place Special Tool 8807-2 (1) on the end of the extension.
  4. Insert lugs on Special Tool 8807-2 into notches in face of caliper piston (5).
  5. Thread the screw drive on 8807-1 down until it contacts the top of 8807-2 which is against the caliper piston. Do not over tighten the screw-drive. Damage to the piston can occur.
  6. Turn 8807-2 with the ratchet, rotating the piston in a clockwise direction until fully seated (bottomed) in the bore. It may be necessary to turn 8807-1 with 8807-2 to start the process of piston retraction.

Brakes
Fig. 129: REAR BRAKE PADS

2. Make sure abutment shims (4) are in place on both upper and lower slide abutments of caliper adapter (3).

NOTE: If the brake pads have a protective paper on the rear face of the brake pad plate, it must be removed before pad installation.

3. Place the brake pads (2, 5) in the abutment shims (3) clipped into the disc brake caliper adapter bracket (3) as shown.

Brakes
Fig. 130: REAR CALIPER MOUNTING

CAUTION: Use care when installing the caliper (2) onto the adapter bracket to avoid damaging the guide pin boots.

4. Install the disc brake caliper (2) over the brake pads on the brake caliper adapter bracket (3).

CAUTION: When removing or installing a caliper guide pin bolt, it is necessary to hold the guide pin stationary while turning the bolt. Hold the guide pin stationary using a wrench placed upon the pin's hex-shaped head.

5. Align the caliper guide pin bolt holes with the adapter bracket. Install the upper and lower caliper guide pin bolts (1). Tighten the guide pin bolts to 35 N.m (26 ft. lbs.).

Brakes
Fig. 131: TIRE AND WHEEL MOUNTING

6. Install tire and wheel assembly (1). Install and tighten wheel mounting nuts (3) to 135 N.m (100 ft. lbs.).

7. Lower vehicle.

8. Pump brake pedal several times to ensure vehicle has a firm brake pedal before moving vehicle.

9. Check and adjust brake fluid level as necessary.

10. Road test vehicle and make several stops to wear off any foreign material on brakes and to seat brake pads.

    Removal
    1. Raise and support vehicle. NOTE: Perform 2 through 5 on each side of vehicle to complete pad set removal. Fig. 124: TIRE AND WHEEL MOUNTING 2. Remove wheel mounting nuts (3), then tire ...

    See also:

    Disassembly
    NOTE: The rear heater-A/C housing must be removed from the vehicle for service of the mode door actuator and blend door actuator and it must be disassembled for service of the A/C evaporator ...

    ENGINE BLOCK HEATER — IF EQUIPPED
    The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. ...

    Reservoir, brake master cylinder
    Removal CAUTION: If at any time the master cylinder is loosened or removed, you must perform the master cylinder installation procedure to ensure that the seal (o-ring) is still ...

    0.0199