Dodge Journey: Removal, Installation
REMOVAL
REMOVAL - NGC CONTROLLER
Fig. 39: Remove/Install PCM
NOTE: USE THE SCAN TOOL TO REPROGRAM THE NEW POWERTRAIN CONTROL MODULE (PCM) WITH THE VEHICLES ORIGINAL IDENTIFICATION NUMBER (VIN) AND THE VEHICLES ORIGINAL MILEAGE. IF THIS STEP IS NOT DONE, A DIAGNOSTIC TROUBLE CODE (DTC) MAY BE SET.
To avoid possible voltage spike damage to PCM, ignition key must be off, and the negative battery cable must be disconnected before unplugging the PCM connectors.
1. Disconnect and isolate the negative battery cable.
2. Unlock and disconnect the 4 electrical connectors at the PCM.
Fig. 40: Mounting Screws/Electrical Connectors
3. Remove the 3 fasteners (1) holding the PCM to the bracket.
REMOVAL - GPEC CONTROLLER (2.4L)
Fig. 41: GPEC Controller
- - Connectors
- - PCM
NOTE: USE THE SCAN TOOL TO REPROGRAM THE NEW POWERTRAIN CONTROL MODULE (PCM) WITH THE VEHICLES ORIGINAL IDENTIFICATION NUMBER (VIN) AND THE VEHICLES ORIGINAL MILEAGE. IF THIS STEP IS NOT DONE, A DIAGNOSTIC TROUBLE CODE (DTC) MAY BE SET.
To avoid possible voltage spike damage to PCM, ignition key must be off, and the negative battery cable must be disconnected before unplugging the PCM connectors.
1. Disconnect and isolate the negative battery cable.
2. Unlock and disconnect the 2 electrical connectors (1) at the PCM (2).
Fig. 42: GPEC Controller Mounting
- - Bracket
- - PCM
- - Bolts
3. Remove the 4 bolts (3) holding the PCM (2) to the bracket (1) and remove the PCM (2) from the vehicle.
INSTALLATION
INSTALLATION - NGC CONTROLLER
Fig. 43: Mounting Screws/Electrical Connectors
NOTE: USE THE SCAN TOOL TO REPROGRAM THE NEW POWERTRAIN CONTROL MODULE (PCM) WITH THE VEHICLES ORIGINAL IDENTIFICATION NUMBER (VIN) AND THE VEHICLES ORIGINAL MILEAGE. IF THIS STEP IS NOT DONE, A DIAGNOSTIC TROUBLE CODE (DTC) MAY BE SET.
1. Install PCM to bracket with 3 fasteners (1).
Fig. 44: Remove/Install PCM
2. Install and lock the 4 electrical connectors to the PCM.
3. Connect negative battery cable, tighten nut to 5 N.m (45 in. lbs.).
4. Use the scan tool to reprogram new PCM with vehicles original Identification Number (VIN) and original vehicle mileage.
INSTALLATION - GPEC CONTROLLER (2.4L)
Fig. 45: GPEC Controller Mounting
- - Bracket
- - PCM
- - Bolts
NOTE: USE THE SCAN TOOL TO REPROGRAM THE NEW POWERTRAIN CONTROL MODULE (PCM) WITH THE VEHICLES ORIGINAL IDENTIFICATION NUMBER (VIN) AND THE VEHICLES ORIGINAL MILEAGE. IF THIS STEP IS NOT DONE, A DIAGNOSTIC TROUBLE CODE (DTC) MAY BE SET.
1. Install PCM (2) to bracket (1) with 4 bolts (3).
Fig. 46: GPEC Controller
- - Connectors
- - PCM
2. Install and lock the 2 electrical connectors (1) to the PCM (2).
3. Connect negative battery cable, tighten nut to 5 N.m (45 in. lbs.).
4. Use the scan tool to reprogram new PCM with vehicles original Identification Number (VIN) and original vehicle mileage.
Standard procedure
PCM/ECM REPROGRAMMING - GAS Follow the instructions in order. OBTAINING DIAGNOSTIC TROUBLE CODES BULB CHECK Key on: Bulb illuminated until vehicle starts, as long as all once per trip (readiness ...Module, steering column
DESCRIPTION Fig. 47: Steering Control Module This vehicle is equipped with a Steering Control Module (SCM) that is internal to the left multi-function switch housing (2). The left (lighting) mu ...See also:
Filter, engine oil
Removal
Fig. 256: Oil Filter & Drain Plug
1. Raise vehicle on hoist.
2. Position a suitable collecting container under oil filter location.
3. Remove oil filter (2) using a suitable oil ...
Installation
NOTE: LHD model shown in illustrations. RHD model similar.
RIGHT FRONT FLOOR DUCT
Fig. 71: Duct-Right Front Floor PM
NOTE: Illustration shown with instrument panel removed for clarity.
...
Description
Fig. 246: Liquid/Suction Line Assembly with Rear A/C
NOTE: A/C liquid and suction line assembly with rear A/C shown. Front
A/C only line
assembly similar.
The A/C liquid line is serviced ...