Dodge Journey: Removal, Installation

REMOVAL

Automatic Transmission 41TE
Fig. 298: Identifying Transmission Connectors

  1. - SOLENOID PACK CONNECTOR
  2. - INPUT SPEED SENSOR CONNECTOR
  3. - OUTPUT SPEED SENSOR CONNECTOR
  4. - TRANSMISSION RANGE SENSOR CONNECTOR

NOTE: If solenoid/pressure switch assembly is being replaced, the "Quick-Learn" procedure must be performed.

1. Disconnect battery negative cable.

2. Remove air cleaner assembly.

3. Disconnect solenoid/pressure switch assembly connector (1) .

4. Disconnect input speed sensor connector (2).

Automatic Transmission 41TE
Fig. 299: Removing/Installing Input Speed Sensor

  1. - INPUT SPEED SENSOR

5. Remove input speed sensor (1) .

Automatic Transmission 41TE
Fig. 300: Removing/Installing Solenoid/Pressure Switch Assembly-To-Transaxle Case Bolts

  1. - BOLTS
  2. - SOLENOID AND PRESSURE SWITCH ASSEMBLY

6. Remove three solenoid/pressure switch assembly-to-transaxle case bolts (1) .

Automatic Transmission 41TE
Fig. 301: Removing/Installing Solenoid/Pressure Switch Assembly & Gasket

  1. - SOLENOID/PRESSURE SWITCH ASSEMBLY
  2. - GASKET

7. Remove solenoid/pressure switch assembly (1) and gasket (2). Use care to prevent gasket material and foreign objects from become lodged in the transaxle case ports.

INSTALLATION

Automatic Transmission 41TE
Fig. 302: Removing/Installing Solenoid/Pressure Switch Assembly & Gasket

  1. - SOLENOID/PRESSURE SWITCH ASSEMBLY
  2. - GASKET

NOTE: If solenoid/pressure switch assembly is being replaced, it is necessary to perform the "Quick-Learn" procedure.

1. Install solenoid/pressure switch assembly and new gasket to transaxle .

Automatic Transmission 41TE
Fig. 303: Removing/Installing Solenoid/Pressure Switch Assembly-To-Transaxle Case Bolts

  1. - BOLTS
  2. - SOLENOID AND PRESSURE SWITCH ASSEMBLY

2. Install and torque three bolts (1) to 12 N.m (105 in. lbs.).

Automatic Transmission 41TE
Fig. 304: Removing/Installing Input Speed Sensor

  1. - INPUT SPEED SENSOR

3. Install input speed sensor (1) and torque to 27 N.m (20 ft. lbs.).

Automatic Transmission 41TE
Fig. 305: Identifying Transmission Connectors

  1. - SOLENOID PACK CONNECTOR
  2. - INPUT SPEED SENSOR CONNECTOR
  3. - OUTPUT SPEED SENSOR CONNECTOR
  4. - TRANSMISSION RANGE SENSOR CONNECTOR

4. Connect input speed sensor connector (2) .

5. Install solenoid/pressure switch 8-way connector and torque to 4 N.m (35 in. lbs.).

6. Install air cleaner assembly.

7. Connect battery negative cable.

8. If solenoid/pressure switch assembly was replaced, perform the "Quick-Learn" procedure.

    Description, Operation
    DESCRIPTION Fig. 297: Identifying Solenoid/Pressure Switch Assembly - SOLENOID AND PRESSURE SWITCH ASSEMBLY The Solenoid/Pressure Switch Assembly (1) is external to the transaxle and mount ...

    Cable, shift
    REMOVAL Fig. 306: Identifying Knee Blocker 1. Remove the knee blocker (2). Fig. 307: Identifying Shift Cable At Shifter NOTE: Ensure the lock tab on the shift cable (2) is depressed before ...

    See also:

    Diagnosis and Testing
    SUSPENSION AND STEERING CONDITION POSSIBLE CAUSES CORRECTION Front End Whine On Turns 1. Defective Wheel Bearing2. Incorrect Wheel Alignment 3. Worn Tires ...

    Removal, Installation
    REMOVAL WARNING: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negat ...

    Installation
    Fig. 25: Ball Joint Installation 1. Install Installer (2), Special Tool 9964-1, and Installer (4), Special Tool 9964-2 on Remover/Installer (5), Special Tool 8441-1. Place a new ball joint (stem ...


    0.0101